 |
Caracteristicas
The Agilent 34937A is a general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 28 independent single-pole, double-throw (SPDT) 1A relays and 4 single-pole, single-throw (Form A) 5A relays. This module is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. The Form C channels are 300V, 1A contacts and can handle up to 50W, and the Form A channels are 30VDC/250VAC, 5A contacts and can handle up to 150W. Standard 50-pin Dsub connectors allow for use with standard cables, terminal blocks, or mass interconnect solutions.
28 Form C channels up to 1A, 50W
4 Form A channels up to 5A, 150W
Latching armature relays, with relay counter
Temperature sensor for overheating conditions
Simultaneous channel switching
|
Low Frequency Modules |
| Module |
Description |
Max Volts |
Max Current |
BW (MHz) |
Scan Ch/Sec |
Thermal Offset |
Comments |
| Multiplexers |
| 34921A |
40-ch armature multiplexer w/ low thermal offset |
300 V |
1 A |
45 MHz |
100 |
<3 µV |
· Temp reference · 4 current channels · Config as 2- or 4-wire |
| 34922A |
70-ch armature multiplexer |
300 V |
1 A |
25 MHz |
100 |
<3 µV |
Config as 2- or 4-wire |
| 34923A |
40/80-ch reed multiplexer |
80 V peak |
0.5 A |
45 MHz |
500 |
<50 µV |
Config as 1-, 2- or 4-wire |
| 34924A |
70-ch reed multiplexer |
80 V peak |
0.5 A |
25 MHz |
500 |
<50 µV |
Config as 2- or 4-wire |
| 34925A |
40/80-ch optically isolated FET multiplexer |
±80 V |
0.05 A |
1 MHz |
Contact Factory |
<3 µV |
Config as 1-, 2- or 4-wire |
| Matricies |
| 34931A |
Dual 4x8 armature matrix |
300 V |
1 A |
30 MHz |
100 |
<3 µV |
Backplane expandable |
| 34932A |
Dual 4x16 armature matrix |
300 V |
1 A |
30 MHz |
100 |
<3 µV |
Backplane expandable |
| 34933A |
Dual/Quad 4x8 reed matrix |
80 V peak |
0.5 A |
30 MHz |
500 |
<50 µV |
Backplane expandable Config as 1- or 2-wire |
| General Purpose |
| 34937A |
28-ch Form C and 4-channel Form A |
300 V 30 VDC/250 VAC |
1 A 5 A |
10 MHz |
N/A |
3 µV |
|
| 34938A |
20-ch 5 Amp Form A |
30 VDC / 250 VAC |
5 A |
10 MHz |
N/A |
3 µV |
|
| RF and Microwave Modules |
| Module |
Description |
Insertion Loss |
Cross Talk |
Bandwidth |
SWR |
Input Impedence |
Comments |
| 34941A |
Quad 1x4 50 Ù 1.5 GHz RF multiplexer |
Contact factory |
Contact factory |
Contact factory |
Contact factory |
50 Ù |
Specs @ 100 MHz |
| 34942A |
Quad 1x4 75 Ù 1.5 GHz RF multiplexer |
Contact factory |
Contact factory |
Contact factory |
Contact factory |
75 Ù |
Contact factory |
| 34945A |
Microwave switch/attenuator driver |
|
|
|
|
|
|
| 34946A |
Dual 1x2 SPDT terminated microwave switch |
<0.42 dB <0.69 dB |
>85 dB >67dB |
4 GHz or 20 GHz |
<1.15 <1.30 |
50 Ù |
@ 4 GHz @ 20 GHz |
| 34947A |
Triple 1x2 SPDT unterminated microwave switch |
<0.42 dB <0.69 dB |
>85 dB >67 dB |
4 GHz or 20 GHz |
<1.15 <1.30 |
50 Ù |
@ 4 GHz @ 20 GHz |
| System Control Modules |
| Module |
Description |
|
| 34950A |
64-bit digital I/O with memory and counter |
Eight 8-bit digital I/O channels with programmable polarity, thresholds up to 5 V, 7 handshaking protocols and pattern memory. Two 20 MHz frequency counter/totalizers. |
| 34951A |
4-channel isolated D/A converter with waveform memory |
Output DC voltage up to ±16 V or DC current up to ±20 Output waveforms with a 200 kHz update rate and 16 bits of resolution. Use on-board memory to create waveforms with more than 500,000 points. |
| 34952A |
Multifunction module with 32-bit DIO, 2-ch D/A and totalizer |
Four 8-bit digital I/O channels, two ±12-V analog outputs, and a 100 kHz gated totalizer. |
| 34959A |
Breadboard module |
Create your own custom designs with access to the +12 V and +5 V supplies, 16 GPIO ports and 32 drive lines. |
|
|
 |
 |
 |
 |
|
 |

| Accesorios para este Producto |
|
|
|

|