 |
Caracteristicas
The Agilent 34951A module for the 34980A Multifunction Switch/Measure Unit has four electronically calibrated analog channels that can output up to +/-16V DC or +/-20mA DC with 16 bits of resolution. Each channel can be updated individually with a 200 kHz update rate. You can use the standard waveforms provided or create your own with over 500,000 points. These points can be dynamically allocated among one or more channels and output as a point-to-point arb.
These D/As are useful to source bias voltages to your device under test, to control your analog programmable power supplies, or use the outputs as setpoints for your control systems. Standard 50-pin Dsub connectors allow for use with standard cables, terminal blocks, or mass interconnect solutions.
- Four isolated analog outputs
- Output up to +/-16V DC or +/-20mA DC
- 16-bits of resolution
- 200 kHz update rate
- Default standard waveforms
- Onboard memory to create your own waveforms
|
Low Frequency Modules |
| Module |
Description |
Max Volts |
Max Current |
BW (MHz) |
Scan Ch/Sec |
Thermal Offset |
Comments |
| Multiplexers |
| 34921A |
40-ch armature multiplexer w/ low thermal offset |
300 V |
1 A |
45 MHz |
100 |
<3 µV |
¡¤ Temp reference ¡¤ 4 current channels ¡¤ Config as 2- or 4-wire |
| 34922A |
70-ch armature multiplexer |
300 V |
1 A |
25 MHz |
100 |
<3 µV |
Config as 2- or 4-wire |
| 34923A |
40/80-ch reed multiplexer |
80 V peak |
0.5 A |
45 MHz |
500 |
<50 µV |
Config as 1-, 2- or 4-wire |
| 34924A |
70-ch reed multiplexer |
80 V peak |
0.5 A |
25 MHz |
500 |
<50 µV |
Config as 2- or 4-wire |
| 34925A |
40/80-ch optically isolated FET multiplexer |
¡À80 V |
0.05 A |
1 MHz |
Contact Factory |
<3 µV |
Config as 1-, 2- or 4-wire |
| Matricies |
| 34931A |
Dual 4x8 armature matrix |
300 V |
1 A |
30 MHz |
100 |
<3 µV |
Backplane expandable |
| 34932A |
Dual 4x16 armature matrix |
300 V |
1 A |
30 MHz |
100 |
<3 µV |
Backplane expandable |
| 34933A |
Dual/Quad 4x8 reed matrix |
80 V peak |
0.5 A |
30 MHz |
500 |
<50 µV |
Backplane expandable Config as 1- or 2-wire |
| General Purpose |
| 34937A |
28-ch Form C and 4-channel Form A |
300 V 30 VDC/250 VAC |
1 A 5 A |
10 MHz |
N/A |
3 µV |
|
| 34938A |
20-ch 5 Amp Form A |
30 VDC / 250 VAC |
5 A |
10 MHz |
N/A |
3 µV |
|
| RF and Microwave Modules |
| Module |
Description |
Insertion Loss |
Cross Talk |
Bandwidth |
SWR |
Input Impedence |
Comments |
| 34941A |
Quad 1x4 50 Ù 1.5 GHz RF multiplexer |
Contact factory |
Contact factory |
Contact factory |
Contact factory |
50 Ù |
Specs @ 100 MHz |
| 34942A |
Quad 1x4 75 Ù 1.5 GHz RF multiplexer |
Contact factory |
Contact factory |
Contact factory |
Contact factory |
75 Ù |
Contact factory |
| 34945A |
Microwave switch/attenuator driver |
|
|
|
|
|
|
| 34946A |
Dual 1x2 SPDT terminated microwave switch |
<0.42 dB <0.69 dB |
>85 dB >67dB |
4 GHz or 20 GHz |
<1.15 <1.30 |
50 Ù |
@ 4 GHz @ 20 GHz |
| 34947A |
Triple 1x2 SPDT unterminated microwave switch |
<0.42 dB <0.69 dB |
>85 dB >67 dB |
4 GHz or 20 GHz |
<1.15 <1.30 |
50 Ù |
@ 4 GHz @ 20 GHz |
| System Control Modules |
| Module |
Description |
|
| 34950A |
64-bit digital I/O with memory and counter |
Eight 8-bit digital I/O channels with programmable polarity, thresholds up to 5 V, 7 handshaking protocols and pattern memory. Two 20 MHz frequency counter/totalizers. |
| 34951A |
4-channel isolated D/A converter with waveform memory |
Output DC voltage up to ¡À16 V or DC current up to ¡À20 Output waveforms with a 200 kHz update rate and 16 bits of resolution. Use on-board memory to create waveforms with more than 500,000 points. |
| 34952A |
Multifunction module with 32-bit DIO, 2-ch D/A and totalizer |
Four 8-bit digital I/O channels, two ¡À12-V analog outputs, and a 100 kHz gated totalizer. |
| 34959A |
Breadboard module |
Create your own custom designs with access to the +12 V and +5 V supplies, 16 GPIO ports and 32 drive lines. |
|
|
 |
 |
 |
 |
|
 |

| Accesorios para este Producto |
|
|
|

|