Especificaciones

CRT
Type	6-inch rectangular type with internal graticule; 0%, 10%, 90% and 100% markers. 8 x 10 div (1 div = 1 cm)
Accelerating Potential	16 kV approx.
Illumination	Continuously adjustable
Z-axis input	Coupling : DC Sensitivity: 5V or more Maximum input voltage : 30V (DC + AC peak) at 1kHz or less Bandwidth : DC ~ 5 MHz
VERTICAL SYSTEM
Sensitivity	2mV~5V/div, 11 step in 1-2-5 sequence
Sensitivity Accuracy	�…3% (5div at the center of display)
Vernier Vertical Sensitivity	Continuously variable to 1/2.5 or less of panel-indicate value
Bandwidth(-3dB)	DC~100MHz(2mV/div:DC~20MHz)
Rise Time	3.5ns (2mV/div:17.5ns)
Signal Delay	Leading edge can be monitored
Max. Input Voltage	400V(DC+AC peak) at 1kHz or less
Input Coupling	AC, DC, GND
Input Impedance	1Mƒ¶�}2% // approx. 25pF
Vertical Mode	CH1,CH2,DUAL(CHOP/ALT), ADD, CH2 INV.
Bandwidth Limited	20MHz
Common-Mode Rejection Ratio	50:1 or better at 50kHz
Dynamic Range	8 div at 100MHz
HORIZONTAL SYSTEM
Horizontal Modes	MAIN(A), ALT, DELAY(B)
A(main) Sweep Time	50ns~0.5s/div, continuously variable (UNCAL)
B(delay) Sweep Time	50ns~50ms/div
Accuracy	�}3% (�}5% at x 10 MAG)
Sweep Magnification	x 10 (maximum sweep time 5nS/div)
Hold Off Time	Variable
Delay Time	1ƒÊs~5s
Delay Jitter	Better than 1:20000
Alternate Separation	Variable
TRIGGER
Trigger Modes	AUTO, NORM,TV
Trigger Source	CH1, CH2, LINE, EXT
Trigger Coupling	AC, DC, HFR, LFR
Trigger Slope	"+" or "-" polarity or TVsync polarity
Trigger Sensitivity	Mode Frequency INT EXT AUTO 10Hz~20MHz 20MHz~100MHz 0.35div 1.5div 50mV 150mV NORM DC~20MHz 20MHz~100MHz 0.35div 1.5div 50mV 150mV TV sync signal 1div 200mVpp
TV sync	TV-V, TV-H
Max. External Input Voltage	400V(DC+AC peak) at 1kHz
External Input Impedance	1Mƒ¶�}5% // approx.25pF
X-Y OPERATION
Mode	X-axis: selectable CH1, CH2, EXT Y-axis: selectable CH1, CH2, CH1 and CH2
Sensitivity Accuracy	2mV~5V/div�}3% ; EXT : 0.1V/div�}5%
X-axis Bandwidth	DC~500kHz(-3dB)
Phase Error	3�‹ or less from DC~50kHz
OUTPUT SIGNAL
Trigger Signal Output	Voltage: approx. 25mV/div into 50Ħ Frequency response : DC ~ 10MHz
Calibrator Output	1kHz Square wave, 2Vpp�}2%
CURSOR READOUT FUNCTION
Cursor Measurement Function	ĢV, ĢV%, ĢVdB, ĢT, 1/ ĢT, ĢT%, ĢĮ
Cursor Resolution	1/100 DIV
Effective Cursor Range	Vertical: �}3div ; Horizontal: �}4 div
Panel Setting Display	Vertical: V/div(CH1,CH2),UNCAL,ALT/CHOP/ADD,INV, probe factor,AC/DC/GND Horizontal: s/div(MTB, DTB), UNCAL, x 10MAG, delay time , HO Trigger: source, coupling, slope, level, TV-V, TV-H Others: X-Y, lock, save/recall MEM 0-9
AUTO MEASUREMENT FUNCTION
Parameter Function	FREQ, PERIOD,�}WIDTH,�}DUTY (+ or - polarity selected by trigger slope)
Display Digits	Max. 6-digits, decimal
Frequency Range	50Hz ~ 100MHz
Accuracy	1kHz ~ 100MHz : �}0.01% ; 50Hz ~ 1kHz : �}0.05%
Measuring Sensitivity	> 2 div (Measuring source selected from CH1 and Ch2 as synchronous signal sources)
SPECIAL FUNCTION
TIME/DIV Auto Range	Provided
Panel Setting Save & Recall	10 sets
Panel Setups Lock	Provided
POWER SOURCE
	AC 100V/120V/230V�}10% , 50/60Hz
ACCESSORIES
	User manual x 1 Power cord x 1 GTP-100A Probe (10:1/1:1) x 2
DIMENSIONS & WEIGHT
	310(W) x 150(H) x 455(D) mm Approx. 9kg