External Interfaces |
|
CompactPCI BUS Interface |
Compliant with CompactPCI sepcification PICMG 2.0 R3.0
- System master operation
- 64-bit /33 MHz master interface
- 3.3 V/5.0 V compatible (default is 5.0 V)
|
|
SERIAL |
|
COM1 and COM2 |
- Dual UART, 16C550 compatible
- RS-232, RS-422, or RS-485 configurable
- COM1: 9-pin D-sub connector on front panel
- COM2 (through rear panel I/O): RS-232, RS-422, or RS-485 compatible
|
|
COM3 and COM4 |
- 16C550 compatible UARTs
- TTl level signals
- Rear I/O interfacing only
|
|
Parallel |
Multi-Mode™ Parallel I/O interface:
- Standard mode IBM PC/AT and PS/2 compatible
- i-directional parallel I/O interface
- TTl level signals
- Rear I/O interfacing only
|
|
USB Interface |
Five USB 2.0 ports supporting UHCI and EHCI:
- Two USB type connectors on the front panel
- Two rear I/O interfaces
- One on-board port connector
|
|
Gigabit Ethernet |
Two 10/100/1000 MB/s Gigabit Ethernet interfaces based on the Intel 82540EM (Kenai-32) Ethernet PCI bus controller:
- Two RJ-45 connectors on front panel
- Support for two Gigabit Ethernet channels on packet switching backplane (PICMG 2.16, R1.0 compliant)
- Any given channel may only be operated at one or the other of the above interfacing points
- Automatic mode recognition
- Automatic cabling configuration recognition
Cabling requirement: CAT 5, UTP, two-pair cable |
|
Fast Ethernet |
10Base-T/100Base-TX Intel 82559 Fast Ethernet Controller integrated within the ICH4 controller (82559-style):
- One RJ-45 connector on front panel
- Support for one channel of rear I/O interfacing
- May only be operated at one or the other of the above interfaceing options
- Automatic mode recognition
Cabling requirement: CAT 5, UTP, two-pair cable |
|
Internal Interfaces |
|
VGA Interface |
Built-in Intel 3D graphics accelerator for enhanced graphics performance:
- Supports resolutions of up to 2048x1536 by 16-bit at 60 Hz refresh rate
- Hardware motion compensation for software MPEG2 and MPEG4 decoding
- Flexible allocation of video memory up to 64 MB
- 15-pin D-sub VGA CRT-display connector with analog video signals
|
|
Keyboard and Mouse |
- Rear I/O interfacing for both keyboard and mouse
- Separate on-board keyboard connector (5-pin); requires adapter to connect regular keyboard
|
|
MASS STORAGE |
|
EIDE Ultra ATA/100/66/33 |
- Two interfaces
- Up to four devices (hard disks or CD-ROMs)
- 40-pin, 2.54 mm, male pin row connector (standard)
- Optional 44-pin, 2.0 mm, male pin row connector for mounting 2.5" disk drive on board
|
|
CompactFlash |
- CompactFlash type II socket (true IDE mode)
- Supports type I and II CompactFlash cards and IBM Microdrive™
|
|
LPC |
I/O extension interface:
- 22-pin female, pin row connector
- Supports up to two LPC devices
- Designed to support custom, fixed mounted mezzanine boards
|
|
PMC |
CMC/PMC IEEE P1386/Draft 2.4a compliant mezzanine interface:
- Jn1, Jn2, and Jn4 PCI mezzanine connectors for standard PMC modules
- 32-bit/33 MHz master interface
- 3.3 V or 5.0 V compatible
- Rear I/O supported through CompactPCI J5 connector
|
|
Monitor and Control |
|
Watchdog |
Software configurable Watchdog generates IRQ, NMI, or hardware reset. |
|
Thermal Management |
CPU over temperature protection is provided by:
- Internal processor temperature control unit
- CPU shut down via hardware monitor
- Custom designed heat sinks
|
|
System Monitor |
LM81 hardware monitor supervision of:
- System power voltages: +12 V, -12 V, +5 V, +3.3 V, and VCORE
- RTC battery voltage
- Up to two fan speed inputs
|
|
CPU Temperature Monitor |
MAX 1617 hardware monitor supervision of:
- On-die CPU temperature
- CPU surrounding board temperature
|
|
Environmental |
|
Mechanical |
6U, 4HP, CompactPCI/PXI compliant form factor |
|
Operating Temperature |
0˚C to 60˚C -25˚C to 75˚C (optional - only with designated CPU types) |
|
Storage Temperature |
-55˚C to 85˚C |
|
Humidity |
93% RH at 40˚C, non-condensing |
|
Physical |
|
Mechanical |
6U PXI |
|
Dimensions |
233.35 mm x 160 mm |
|
Weight |
546 g (4HP variants with heat sink and without mezzanine boards) |
|
Battery |
3.0 V lithium battery for RTC with battery socket. Recommended types: VARTA CR2025 and Panasonic BR2020 |